1. Home
  2. College physics ii
  3. Fluid statics
  4. Gauge pressure, absolute pressure

10.6 Gauge pressure, absolute pressure, and pressure measurement  (Page 3/7)

<< Chapter < Page
  College physics ii     Page 3 / 7
Chapter >> Page >

Systolic pressure

Systolic pressure is the maximum blood pressure.

Diastolic pressure

Diastolic pressure is the minimum blood pressure.

U.S. Army Spc. Monica Brown takes a soldier's blood pressure reading at the hospital on Forward Operating Base Salerno, Afghanistan, March 10, 2008.
In routine blood pressure measurements, an inflatable cuff is placed on the upper arm at the same level as the heart. Blood flow is detected just below the cuff, and corresponding pressures are transmitted to a mercury-filled manometer. (credit: U.S. Army photo by Spc. Micah E. Clare\4TH BCT)

Calculating height of iv bag: blood pressure and intravenous infusions

Intravenous infusions are usually made with the help of the gravitational force. Assuming that the density of the fluid being administered is 1.00 g/ml, at what height should the IV bag be placed above the entry point so that the fluid just enters the vein if the blood pressure in the vein is 18 mm Hg above atmospheric pressure? Assume that the IV bag is collapsible.

Strategy for (a)

For the fluid to just enter the vein, its pressure at entry must exceed the blood pressure in the vein (18 mm Hg above atmospheric pressure). We therefore need to find the height of fluid that corresponds to this gauge pressure.

Solution

We first need to convert the pressure into SI units. Since 1.0 mm Hg = 133 Pa ,

P = 18 mm Hg × 133 Pa 1.0 mm Hg = 2400 Pa . size 12{P="18"`"mm"`"Hg" times { {"133"`"Pa"} over {1 "." 0`"mm"`"Hg"} } ="2400"`"Pa" "." } {}

Rearranging P g = hρg size 12{P rSub { size 8{g} } =hρg} {} for h size 12{h} {} gives h = P g ρg size 12{h= { {P rSub { size 8{g} } } over {ρg} } } {} . Substituting known values into this equation gives

h = 2400 N /m 2 1 . 0 × 10 3 kg/m 3 9 . 80 m/s 2 = 0.24 m. alignl { stack { size 12{h= { {"2400"`"N/m" rSup { size 8{2} } } over { left (1 "." 0 times "10" rSup { size 8{3} } `"kg/m" rSup { size 8{3} } right ) left (9 "." "80"`"m/s" rSup { size 8{2} } right )} } } {} #" "=" 0" "." "24"`m "." {} } } {}

Discussion

The IV bag must be placed at 0.24 m above the entry point into the arm for the fluid to just enter the arm. Generally, IV bags are placed higher than this. You may have noticed that the bags used for blood collection are placed below the donor to allow blood to flow easily from the arm to the bag, which is the opposite direction of flow than required in the example presented here.

A barometer is a device that measures atmospheric pressure. A mercury barometer is shown in [link] . This device measures atmospheric pressure, rather than gauge pressure, because there is a nearly pure vacuum above the mercury in the tube. The height of the mercury is such that hρg = P atm size 12{hρg=P rSub { size 8{"atm"} } } {} . When atmospheric pressure varies, the mercury rises or falls, giving important clues to weather forecasters. The barometer can also be used as an altimeter, since average atmospheric pressure varies with altitude. Mercury barometers and manometers are so common that units of mm Hg are often quoted for atmospheric pressure and blood pressures. [link] gives conversion factors for some of the more commonly used units of pressure.

Mercury barometer has an evacuated glass tube inverted and placed in the mercury container. The height of the mercury column in the inverted tube is determined by the atmospheric pressure.
A mercury barometer measures atmospheric pressure. The pressure due to the mercury’s weight, hρg size 12{hρg} {} , equals atmospheric pressure. The atmosphere is able to force mercury in the tube to a height h size 12{h} {} because the pressure above the mercury is zero.
Conversion factors for various pressure units
Conversion to N/m 2 (Pa) Conversion from atm
1.0 atm = 1 . 013 × 10 5 N/m 2 size 12{1 "." 0`"atm"=1 "." "013" times "10" rSup { size 8{5} } `"N/m" rSup { size 8{2} } } {} 1.0 atm = 1 . 013 × 10 5 N/m 2 size 12{1 "." 0`"atm"=1 "." "013" times "10" rSup { size 8{5} } `"N/m" rSup { size 8{2} } } {}
1.0 dyne/cm 2 = 0 . 10 N/m 2 size 12{1 "." 0`"dyne/cm" rSup { size 8{2} } =0 "." "10"`"N/m" rSup { size 8{2} } } {} 1 . 0 atm = 1 . 013 × 10 6 dyne/cm 2 size 12{1 "." 0`"atm"=1 "." "013" times "10" rSup { size 8{6} } `"dyne/cm" rSup { size 8{2} } } {}
1 . 0 kg/cm 2 = 9 . 8 × 10 4 N/m 2 size 12{1 "." 0`"kg/cm" rSup { size 8{2} } =9 "." 8 times "10" rSup { size 8{4} } `"N/m" rSup { size 8{2} } } {} 1 . 0 atm = 1 . 013 kg/cm 2 size 12{1 "." 0`"atm"=1 "." "013"`"kg/cm" rSup { size 8{2} } } {}
1 . 0 lb/in . 2 = 6 . 90 × 10 3 N/m 2 size 12{1 "." 0`"lb/in" "." rSup { size 8{2} } =6 "." "90" times "10" rSup { size 8{3} } `"N/m" rSup { size 8{2} } } {} 1 . 0 atm = 14 . 7 lb/in . 2 size 12{1 "." 0`"atm"="14" "." 7`"lb/in" "." rSup { size 8{2} } } {}
1.0 mm Hg = 133 N/m 2 size 12{1 "." 0`"mm"`"Hg"="133"`"N/m" rSup { size 8{2} } } {} 1 . 0 atm = 760 mm Hg size 12{1 "." 0`"atm"="760"`"mm"`"Hg"} {}
1 . 0 cm Hg = 1 . 33 × 10 3 N/m 2 size 12{1 "." 0`"cm"`"Hg"=1 "." "33" times "10" rSup { size 8{3} } `"N/m" rSup { size 8{2} } } {} 1 . 0 atm = 76 . 0 cm Hg size 12{1 "." 0`"atm"="76" "." 0`"cm"`"Hg"} {}
1 . 0 cm water = 98 . 1 N/m 2 size 12{1 "." 0`"cm"`"water"="98" "." 1`"N/m" rSup { size 8{2} } } {} 1 . 0 atm = 1 . 03 × 10 3 cm water size 12{1 "." 0`"atm"=1 "." "03" times "10" rSup { size 8{3} } `"cm"`"water"} {}
1.0 bar = 1 . 000 × 10 5 N/m 2 size 12{1 "." 0`"bar"=1 "." "000" times "10" rSup { size 8{5} } `"N/m" rSup { size 8{2} } } {} 1 . 0 atm = 1.013 bar size 12{1 "." 0`"atm"=1 "." "013"`"bar"} {}
1.0 millibar = 1 . 000 × 10 2 N/m 2 size 12{1 "." 0`"millibar"=1 "." "000" times "10" rSup { size 8{2} } `"N/m" rSup { size 8{2} } } {} 1.0 atm = 1013 millibar

Section summary

  • Gauge pressure is the pressure relative to atmospheric pressure.
  • Absolute pressure is the sum of gauge pressure and atmospheric pressure.
  • Aneroid gauge measures pressure using a bellows-and-spring arrangement connected to the pointer of a calibrated scale.
  • Open-tube manometers have U-shaped tubes and one end is always open. It is used to measure pressure.
  • A mercury barometer is a device that measures atmospheric pressure.

Conceptual questions

Explain why the fluid reaches equal levels on either side of a manometer if both sides are open to the atmosphere, even if the tubes are of different diameters.

[link] shows how a common measurement of arterial blood pressure is made. Is there any effect on the measured pressure if the manometer is lowered? What is the effect of raising the arm above the shoulder? What is the effect of placing the cuff on the upper leg with the person standing? Explain your answers in terms of pressure created by the weight of a fluid.

Considering the magnitude of typical arterial blood pressures, why are mercury rather than water manometers used for these measurements?

Problems&Exercises

Find the gauge and absolute pressures in the balloon and peanut jar shown in [link] , assuming the manometer connected to the balloon uses water whereas the manometer connected to the jar contains mercury. Express in units of centimeters of water for the balloon and millimeters of mercury for the jar, taking h = 0 . 0500 m size 12{h=0 "." "0500"`m} {} for each.

Balloon:

P g = 5.00 cm H 2 O, P abs = 1.035 × 10 3 cm H 2 O. alignl { stack { size 12{P rSub { size 8{g} } =5 "." "00"`"cm"`H rSub { size 8{2} } "O,"} {} #P rSub { size 8{"abs"} } =1 "." "035" times "10" rSup { size 8{3} } `"cm"`H rSub { size 8{2} } O "." {} } } {}

Jar:

P g = − 50.0 mm Hg , P abs = 710 mm Hg. alignl { stack { size 12{P rSub { size 8{g} } = - "50" "." 0`"mm"`"Hg,"} {} #P rSub { size 8{"abs"} } ="710"`"mm"`"Hg" "." {} } } {}

(a) Convert normal blood pressure readings of 120 over 80 mm Hg to newtons per meter squared using the relationship for pressure due to the weight of a fluid ( P = hρg ) size 12{ \( P=hρg \) } {} rather than a conversion factor. (b) Discuss why blood pressures for an infant could be smaller than those for an adult. Specifically, consider the smaller height to which blood must be pumped.

How tall must a water-filled manometer be to measure blood pressures as high as 300 mm Hg?

4.08 m

Pressure cookers have been around for more than 300 years, although their use has strongly declined in recent years (early models had a nasty habit of exploding). How much force must the latches holding the lid onto a pressure cooker be able to withstand if the circular lid is 25.0 cm size 12{"25" "." 0`"cm"} {} in diameter and the gauge pressure inside is 300 atm? Neglect the weight of the lid.

Suppose you measure a standing person’s blood pressure by placing the cuff on his leg 0.500 m below the heart. Calculate the pressure you would observe (in units of mm Hg) if the pressure at the heart were 120 over 80 mm Hg. Assume that there is no loss of pressure due to resistance in the circulatory system (a reasonable assumption, since major arteries are large).

Δ P = 38.7 mm Hg, Leg blood pressure = 159 119 . alignl { stack { size 12{ΔP="38" "." 7`"mm"`"Hg,"} {} #size 12{"Leg"`"blood"`"pressure"= { {"159"} over {"119"} } "." } {} } } {}

A submarine is stranded on the bottom of the ocean with its hatch 25.0 m below the surface. Calculate the force needed to open the hatch from the inside, given it is circular and 0.450 m in diameter. Air pressure inside the submarine is 1.00 atm.

Assuming bicycle tires are perfectly flexible and support the weight of bicycle and rider by pressure alone, calculate the total area of the tires in contact with the ground. The bicycle plus rider has a mass of 80.0 kg, and the gauge pressure in the tires is 3 . 50 × 10 5 Pa size 12{3 "." "50" times "10" rSup { size 8{5} } `"Pa"} {} .

22 . 4 cm 2 size 12{"22" "." 4`"cm" rSup { size 8{2} } } {}

Questions & Answers

I'm interested in biological psychology and cognitive psychology
Tanya Reply
what does preconceived mean
sammie Reply
physiological Psychology
Nwosu Reply
How can I develope my cognitive domain
Amanyire Reply
why is communication effective
Dakolo Reply
Communication is effective because it allows individuals to share ideas, thoughts, and information with others.
effective communication can lead to improved outcomes in various settings, including personal relationships, business environments, and educational settings. By communicating effectively, individuals can negotiate effectively, solve problems collaboratively, and work towards common goals.
it starts up serve and return practice/assessments.it helps find voice talking therapy also assessments through relaxed conversation.
miss
Every time someone flushes a toilet in the apartment building, the person begins to jumb back automatically after hearing the flush, before the water temperature changes. Identify the types of learning, if it is classical conditioning identify the NS, UCS, CS and CR. If it is operant conditioning, identify the type of consequence positive reinforcement, negative reinforcement or punishment
Wekolamo Reply
please i need answer
Wekolamo
because it helps many people around the world to understand how to interact with other people and understand them well, for example at work (job).
Manix Reply
Agreed 👍 There are many parts of our brains and behaviors, we really need to get to know. Blessings for everyone and happy Sunday!
ARC
A child is a member of community not society elucidate ?
JESSY Reply
Isn't practices worldwide, be it psychology, be it science. isn't much just a false belief of control over something the mind cannot truly comprehend?
Simon Reply
compare and contrast skinner's perspective on personality development on freud
namakula Reply
Skinner skipped the whole unconscious phenomenon and rather emphasized on classical conditioning
war
explain how nature and nurture affect the development and later the productivity of an individual.
Amesalu Reply
nature is an hereditary factor while nurture is an environmental factor which constitute an individual personality. so if an individual's parent has a deviant behavior and was also brought up in an deviant environment, observation of the behavior and the inborn trait we make the individual deviant.
Samuel
I am taking this course because I am hoping that I could somehow learn more about my chosen field of interest and due to the fact that being a PsyD really ignites my passion as an individual the more I hope to learn about developing and literally explore the complexity of my critical thinking skills
Zyryn Reply
good👍
Jonathan
and having a good philosophy of the world is like a sandwich and a peanut butter 👍
Jonathan
generally amnesi how long yrs memory loss
Kelu Reply
interpersonal relationships
Abdulfatai Reply
What would be the best educational aid(s) for gifted kids/savants?
Heidi Reply
treat them normal, if they want help then give them. that will make everyone happy
Saurabh
Got questions? Join the online conversation and get instant answers!
Jobilize.com Reply
<< Chapter < Page Page > Chapter >>
Practice Key Terms 4

Read also:

Get Jobilize Job Search Mobile App in your pocket Now!

Get it on Google Play Download on the App Store Now




Source:  OpenStax, College physics ii. OpenStax CNX. Nov 29, 2012 Download for free at http://legacy.cnx.org/content/col11458/1.2
Google Play and the Google Play logo are trademarks of Google Inc.

Notification Switch

Would you like to follow the 'College physics ii' conversation and receive update notifications?

Ask