1. Home
  2. University physics volume 2
  3. Unit 2. electricity and magnetism
  4. Direct-current circuits
  5. Kirchhoff's rules

10.3 Kirchhoff's rules  (Page 7/10)

<< Chapter < Page
  University physics volume 2     Page 7 / 10
Chapter >> Page >

Solar cell arrays

Another example dealing with multiple voltage sources is that of combinations of solar cells —wired in both series and parallel combinations to yield a desired voltage and current. Photovoltaic generation, which is the conversion of sunlight directly into electricity, is based upon the photoelectric effect. The photoelectric effect is beyond the scope of this chapter and is covered in Photons and Matter Waves , but in general, photons hitting the surface of a solar cell create an electric current in the cell.

Most solar cells are made from pure silicon. Most single cells have a voltage output of about 0.5 V, while the current output is a function of the amount of sunlight falling on the cell (the incident solar radiation known as the insolation). Under bright noon sunlight, a current per unit area of about 100 mA/cm 2 of cell surface area is produced by typical single-crystal cells.

Individual solar cells are connected electrically in modules to meet electrical energy needs. They can be wired together in series or in parallel—connected like the batteries discussed earlier. A solar-cell array or module usually consists of between 36 and 72 cells, with a power output of 50 W to 140 W.

Solar cells, like batteries, provide a direct current (dc) voltage. Current from a dc voltage source is unidirectional. Most household appliances need an alternating current (ac) voltage.

Summary

  • Kirchhoff’s rules can be used to analyze any circuit, simple or complex. The simpler series and parallel connection rules are special cases of Kirchhoff’s rules.
  • Kirchhoff’s first rule, also known as the junction rule, applies to the charge to a junction. Current is the flow of charge; thus, whatever charge flows into the junction must flow out.
  • Kirchhoff’s second rule, also known as the loop rule, states that the voltage drop around a loop is zero.
  • When calculating potential and current using Kirchhoff’s rules, a set of conventions must be followed for determining the correct signs of various terms.
  • When multiple voltage sources are in series, their internal resistances add together and their emfs add together to get the total values.
  • When multiple voltage sources are in parallel, their internal resistances combine to an equivalent resistance that is less than the individual resistance and provides a higher current than a single cell.
  • Solar cells can be wired in series or parallel to provide increased voltage or current, respectively.

Conceptual questions

Can all of the currents going into the junction shown below be positive? Explain.

The figure shows a junction with three incoming current branches.
Got questions? Get instant answers now!

Consider the circuit shown below. Does the analysis of the circuit require Kirchhoff’s method, or can it be redrawn to simplify the circuit? If it is a circuit of series and parallel connections, what is the equivalent resistance?

The figure shows a circuit with positive terminal of voltage source V connected to three parallel branches. The first branch has resistor R subscript 2 connected to parallel branches with R subscript 4 and R subscript 3 series with R subscript 5. The second branch has resistor R subscript 1 and third branch has resistor R subscript 6.

It can be redrawn.
R eq = [ 1 R 6 + 1 R 1 + 1 R 2 + ( 1 R 4 + 1 R 3 + R 5 ) −1 ] −1

Got questions? Get instant answers now!

Do batteries in a circuit always supply power to a circuit, or can they absorb power in a circuit? Give an example.

Got questions? Get instant answers now!

What are the advantages and disadvantages of connecting batteries in series? In parallel?

In series the voltages add, but so do the internal resistances, because the internal resistances are in series. In parallel, the terminal voltage is the same, but the equivalent internal resistance is smaller than the smallest individual internal resistance and a higher current can be provided.

Got questions? Get instant answers now!

Semi-tractor trucks use four large 12-V batteries. The starter system requires 24 V, while normal operation of the truck’s other electrical components utilizes 12 V. How could the four batteries be connected to produce 24 V? To produce 12 V? Why is 24 V better than 12 V for starting the truck’s engine (a very heavy load)?

Got questions? Get instant answers now!

Problems

Consider the circuit shown below. (a) Find the voltage across each resistor. (b)What is the power supplied to the circuit and the power dissipated or consumed by the circuit?

The figure shows positive terminal of voltage source V subscript 1 of 12 V connected in series to resistor R subscript 1 of 10 kΩ connected in series to resistor R subscript 2 of 20 kΩ connected in series to resistor R subscript 3 of 10 kΩ connected in series to positive terminal of voltage source V subscript 2 of 24 V connected in series to resistor R subscript 4 of 10 kΩ connected in series to resistor R subscript 5 of 10 kΩ.
Got questions? Get instant answers now!

Consider the circuits shown below. (a) What is the current through each resistor in part (a)? (b) What is the current through each resistor in part (b)? (c) What is the power dissipated or consumed by each circuit? (d) What is the power supplied to each circuit?

Part a shows positive terminal of voltage source V subscript 1 of 1.6 V connected to parallel branches, one with resistor R subscript 1 of 2 kΩ and second with positive terminal of voltage source V subscript 2 of 1.4 V and resistor R subscript 3 of 1 kΩ. The two branches are connected back to V subscript 1 through resistor R subscript 2 of 1 kΩ. Part b shows the same circuit as part a but the terminals of V subscript 2 are reversed.

a. I 1 = 0.6 mA , I 2 = 0.4 mA , I 3 = 0.2 mA ;
b. I 1 = 0.04 mA , I 2 = 1.52 mA , I 3 = −1.48 mA ; c. P out = 0.92 mW , P out = 4.50 mW ;
d. P in = 0.92 mW , P in = 4.50 mW

Got questions? Get instant answers now!

Consider the circuit shown below. Find V 1 , I 2 , and I 3 .

The positive terminal of voltage source V subscript 1 is connected to resistance R subscript 1 of 12 Ω with right current I subscript 1 of 2 A connected to two parallel branches, first with resistor R subscript 2 of 6 Ω with upward current I subscript 2 and second with right current I subscript 3, negative terminal of voltage source V subscript 2 of 21 V and resistor R subscript 3 of 5 Ω.
Got questions? Get instant answers now!

Consider the circuit shown below. Find V 1 , V 2 , and R 4 .

The figure shows a circuit with three horizontal branches. The first branch has resistor R subscript 1 of 6 Ω with right current I subscript 1 of 4 A. The second branch has resistor R subscript 2 of 4 Ω with left current I subscript 2 of 3 A and resistor R subscript 3 of 6 Ω with left current I subscript 3 of 1 A. The third branch has resistor R subscript 5 of 4 Ω with left current I subscript 5 of 3 A. The first and second horizontal branches are connected on the right directly and on the left with voltage source V subscript 1 with positive terminal connected to first branch. The second and third horizontal branches are connected on the right directly and on the left with resistor R subscript 4 with upward current I subscript 4 of 1 A. The second and third branches are also connected in the middle with a voltage source V subscript 2 with positive terminal connected to second branch.

V 1 = 42 V , V 2 = 6 V , R 4 = 6 Ω

Got questions? Get instant answers now!

Consider the circuit shown below. Find I 1 , I 2 , and I 3 .

The positive terminal of voltage source V subscript 1 of 24 V is connected to two parallel branches. The first branch has resistor R subscript 1 of 8 Ω with downward current I subscript 1 and second branch connects to positive terminal of voltage source V subscript 2 of 10 V and resistor R subscript 3 of 4 Ω with left current I subscript 3. The two branches are connected to V subscript 1 through resistor R subscript 2 of 6 Ω with left current of I subscript 2.
Got questions? Get instant answers now!

Consider the circuit shown below. (a) Find I 1 , I 2 , I 3 , I 4 , and I 5 . (b) Find the power supplied by the voltage sources. (c) Find the power dissipated by the resistors.

The circuit has four vertical branches. From left to right, first branch has voltage source V subscript 1 of 12 V with positive terminal upward. The second branch has resistor R subscript 1 of 4 Ω with downward current I subscript 1. The third branch has voltage source V subscript 2 of 5 V with positive terminal upward and upward current I subscript 5. The fourth branch has resistor R subscript 4 of 2 Ω with downward current I subscript 4. The first and second branch are connected at the bottom through resistor R subscript 2 of 3 Ω with left current I subscript 2 and second and third branch are connected at the bottom through resistor R subscript 3 of 2 Ω with left current I subscript 3.

a. I 1 = 1.5 A , I 2 = 2 A , I 3 = 0.5 A , I 4 = 2.5 A , I 5 = 2 A ; b. P in = I 2 V 1 + I 5 V 5 = 34 W ;
c. P out = I 1 2 R 1 + I 2 2 R 2 + I 3 2 R 3 + I 4 2 R 4 = 34 W

Got questions? Get instant answers now!

Consider the circuit shown below. Write the three loop equations for the loops shown.

The circuit has four vertical branches. From left to right, first branch has voltage source V subscript 1 with positive terminal upward. The second branch has resistor R subscript 2 with downward current I subscript 2. The third branch has voltage source V subscript 2 with positive terminal upward and downward current I subscript 2. The fourth branch has resistor R subscript 5 with downward current I subscript 5. The first and second branch are connected at the bottom through resistor R subscript 1 and second and third branch are connected at the bottom through resistor R subscript 4 with left current I subscript 4. The second and third branch are connected at the top through resistor R subscript 3 with left current I subscript 3. The current at the top between first and second branch is right I subscript 1.
Got questions? Get instant answers now!

Consider the circuit shown below. Write equations for the three currents in terms of R and V .

The circuit has four vertical branches. From left to right, first branch has voltage source V subscript 1 with positive terminal upward and resistor R. The second branch has resistor R with downward current I subscript 1. The third and fourth branches both have resistor 2 R and are connected to positive terminal of another voltage source V. The current between first and second branch is right I subscript 2 and between second and third branch is left I subscript 3.

I 1 = 3 5 V R , I 2 = 2 5 V R , I 3 = 1 5 V R

Got questions? Get instant answers now!

Consider the circuit shown in the preceding problem. Write equations for the power supplied by the voltage sources and the power dissipated by the resistors in terms of R and V .

Got questions? Get instant answers now!

A child’s electronic toy is supplied by three 1.58-V alkaline cells having internal resistances of 0.0200 Ω in series with a 1.53-V carbon-zinc dry cell having a 0.100 - Ω internal resistance. The load resistance is 10.0 Ω . (a) Draw a circuit diagram of the toy and its batteries. (b) What current flows? (c) How much power is supplied to the load? (d) What is the internal resistance of the dry cell if it goes bad, resulting in only 0.500 W being supplied to the load?

a.
The resistor R subscript L is connected in series with resistor r subscript 2, voltage source ε subscript 2, resistor r subscript 1, voltage source ε subscript 1, resistor r subscript 1, voltage source ε subscript 1, resistor r subscript 1and voltage source ε subscript 1. All voltage sources have upward negative terminals. ;
b. 0.617 A; c. 3.81 W; d. 18.0 Ω

Got questions? Get instant answers now!

Apply the junction rule to Junction b shown below. Is any new information gained by applying the junction rule at e ?

The circuit has three vertical branches. From left to right, first branch has voltage source ε subscript 1 of 18 V and internal resistance 0.5 Ω with positive terminal upward. The second branch has resistor R subscript 2 of 6 Ω with downward current I subscript 3 and voltage source ε subscript 2 of 3 V and internal resistance 0.25 Ω with positive terminal downward. The third branch has voltage source ε subscript 3 of 12 V and internal resistance 0.5 Ω with positive terminal downward. The first and second branch are connected at the top through resistor R subscript 1 of 20 Ω with right current I subscript 1 and bottom through resistor R subscript 4 of 15 Ω. The second and third branch are connected at the top through resistor R subscript 3 of 8 Ω with right current I subscript 2 and bottom through voltage source ε subscript 4 of 18 V with right positive terminal and internal resistance 0.75 Ω.
Got questions? Get instant answers now!

Apply the loop rule to Loop afedcba in the preceding problem.

I 1 r 1 − ε 1 + I 1 R 4 + ε 4 + I 2 r 4 + I 4 r 3 − ε 3 + I 2 R 3 + I 1 R 1 = 0

Got questions? Get instant answers now!

Questions & Answers

what does the ideal gas law states
Joy Reply
Three charges q_{1}=+3\mu C, q_{2}=+6\mu C and q_{3}=+8\mu C are located at (2,0)m (0,0)m and (0,3) coordinates respectively. Find the magnitude and direction acted upon q_{2} by the two other charges.Draw the correct graphical illustration of the problem above showing the direction of all forces.
Kate Reply
To solve this problem, we need to first find the net force acting on charge q_{2}. The magnitude of the force exerted by q_{1} on q_{2} is given by F=\frac{kq_{1}q_{2}}{r^{2}} where k is the Coulomb constant, q_{1} and q_{2} are the charges of the particles, and r is the distance between them.
Muhammed
What is the direction and net electric force on q_{1}= 5µC located at (0,4)r due to charges q_{2}=7mu located at (0,0)m and q_{3}=3\mu C located at (4,0)m?
Kate Reply
what is the change in momentum of a body?
Eunice Reply
what is a capacitor?
Raymond Reply
Capacitor is a separation of opposite charges using an insulator of very small dimension between them. Capacitor is used for allowing an AC (alternating current) to pass while a DC (direct current) is blocked.
Gautam
A motor travelling at 72km/m on sighting a stop sign applying the breaks such that under constant deaccelerate in the meters of 50 metres what is the magnitude of the accelerate
Maria Reply
please solve
Sharon
8m/s²
Aishat
What is Thermodynamics
Muordit
velocity can be 72 km/h in question. 72 km/h=20 m/s, v^2=2.a.x , 20^2=2.a.50, a=4 m/s^2.
Mehmet
A boat travels due east at a speed of 40meter per seconds across a river flowing due south at 30meter per seconds. what is the resultant speed of the boat
Saheed Reply
50 m/s due south east
Someone
which has a higher temperature, 1cup of boiling water or 1teapot of boiling water which can transfer more heat 1cup of boiling water or 1 teapot of boiling water explain your . answer
Ramon Reply
I believe temperature being an intensive property does not change for any amount of boiling water whereas heat being an extensive property changes with amount/size of the system.
Someone
Scratch that
Someone
temperature for any amount of water to boil at ntp is 100⁰C (it is a state function and and intensive property) and it depends both will give same amount of heat because the surface available for heat transfer is greater in case of the kettle as well as the heat stored in it but if you talk.....
Someone
about the amount of heat stored in the system then in that case since the mass of water in the kettle is greater so more energy is required to raise the temperature b/c more molecules of water are present in the kettle
Someone
definitely of physics
Haryormhidey Reply
how many start and codon
Esrael Reply
what is field
Felix Reply
physics, biology and chemistry this is my Field
ALIYU
field is a region of space under the influence of some physical properties
Collete
what is ogarnic chemistry
WISDOM Reply
determine the slope giving that 3y+ 2x-14=0
WISDOM
Another formula for Acceleration
Belty Reply
a=v/t. a=f/m a
IHUMA
innocent
Adah
pratica A on solution of hydro chloric acid,B is a solution containing 0.5000 mole ofsodium chlorid per dm³,put A in the burret and titrate 20.00 or 25.00cm³ portion of B using melting orange as the indicator. record the deside of your burret tabulate the burret reading and calculate the average volume of acid used?
Nassze Reply
how do lnternal energy measures
Esrael
Two bodies attract each other electrically. Do they both have to be charged? Answer the same question if the bodies repel one another.
JALLAH Reply
No. According to Isac Newtons law. this two bodies maybe you and the wall beside you. Attracting depends on the mass och each body and distance between them.
Dlovan
Are you really asking if two bodies have to be charged to be influenced by Coulombs Law?
Robert
like charges repel while unlike charges atttact
Raymond
<< Chapter < Page Page > Chapter >>
Practice Key Terms 3

Read also:

Get Jobilize Job Search Mobile App in your pocket Now!

Get it on Google Play Download on the App Store Now




Source:  OpenStax, University physics volume 2. OpenStax CNX. Oct 06, 2016 Download for free at http://cnx.org/content/col12074/1.3
Google Play and the Google Play logo are trademarks of Google Inc.

Notification Switch

Would you like to follow the 'University physics volume 2' conversation and receive update notifications?

Ask