| << Chapter < Page | Chapter >> Page > |
Instruction set
The MSP430 instruction set consists of 27 core instructions. Additionally, it supports 24 emulated instructions. The core instructions have unique op-codes decoded by the CPU, while the emulated ones need assemblers and compilers to generate their mnemonics.
There are three core-instruction formats:
- Double operand;
- Single operand;
- Program flow control - Jump.
Byte, word and address instructions are accessed using the .B, .W or .A extensions. If the extension is omitted, the instruction is interpreted as a word instruction.
The double operand instruction is formatted as follows:
| 15 | 14 | 13 | 12 | 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| opcode | S-Reg | Ad | B/W | As | D-Reg |
| Bit | Description | |
| 15-12 | opcode | |
| 11-8 | S-Reg | The working register used for the source operand (src) |
| 7 | Ad | The addressing bits responsible for the addressing mode used for the destination operand (dst) |
| 6 | B/W | Byte or word operation:B/W=0: word operation; B/W=1: byte operation |
| 5-4 | As | The addressing bits responsible for the addressing mode used for the source operand (src) |
| 3-0 | D-Reg | The working register used for the destination operand (dst) |
The next table shows the double operand instructions that are not emulated.
| Mnemonic | Operation | Description |
| Arithmetic instructions | ||
| ADD(.B or .W) src,dst | src+dst→dst | Add source to destination |
| ADDC(.B or .W) src,dst | src+dst+C→dst | Add source and carry to destination |
| DADD(.B or .W) src,dst | src+dst+C→dst (dec) | Decimal add source and carry to destination |
| SUB(.B or .W) src,dst | dst+.not.src+1→dst | Subtract source from destination |
| SUBC(.B or .W) src,dst | dst+.not.src+C→dst | Subtract source and not carry from destination |
| Logical and register control instructions | ||
| AND(.B or .W) src,dst | src.and.dst→dst | AND source with destination |
| BIC(.B or .W) src,dst | .not.src.and.dst→dst | Clear bits in destination |
| BIS(.B or .W) src,dst | src.or.dst→dst | Set bits in destination |
| BIT(.B or .W) src,dst | src.and.dst | Test bits in destination |
| XOR(.B or .W) src,dst | src.xor.dst→dst | XOR source with destination |
| Data instructions | ||
| CMP(.B or .W) src,dst | dst-src | Compare source to destination |
| MOV(.B or .W) src,dst | src→dst | Move source to destination |
Depending on the double operand instruction result, the status bits may be affected. The following gives the conditions for setting and resetting the status bits.
| Status bits | ||||
| Mnemonic | V | N | Z | C |
| Arithmetic instructions | ||||
| ADD(.B or .W) src,dst | =1, Arithmetic overflow=0, otherwise | =1, negative result=0, if positive | =1, null result=0, otherwise | =1, carry from result=0, if not |
| ADDC(.B or .W) src,dst | =1, Arithmetic overflow=0, otherwise | =1, negative result=0, if positive | =1, null result=0, otherwise | =1, carry from MSB result=0, if not |
| DADD(.B or .W) src,dst | - | =1, MSB=1=0, otherwise | =1, null result=0, otherwise | =1, result>99(99) |
| SUB(.B or .W) src,dst | =1, Arithmetic overflow=0, otherwise | =1, negative result=0, if positive | =1, null result=0, otherwise | =1, if no borrow=0, otherwise |
| SUBC(.B or .W) src,dst | =1, Arithmetic overflow=0, otherwise | =1, negative result=0, if positive | =1, null result=0, otherwise | =1, if no borrow=0, otherwise |
| Logical and register control instructions | ||||
| AND(.B or .W) src,dst | =0 | =1, MSB result set=0, if not set | =1, null result=0, otherwise | =1, not zero=0, otherwise |
| BIC(.B or .W) src,dst | - | - | - | - |
| BIS(.B or .W) src,dst | - | - | - | - |
| BIT(.B or .W) src,dst | =0 | =1, MSB result set=0, otherwise | =1, null result=0, otherwise | =1, not zero=0, otherwise |
| XOR(.B or .W) src,dst | =1, both operands negative | =1, MSB result set=0, otherwise | =1, null result,=0, otherwise | =1, not zero=0, otherwise |
| Data instructions | ||||
| CMP(.B or .W) src,dst | =1, Arithmetic overflow=0, otherwise | =1, src>=dst=0, src<dst | =1, src=dst=0, otherwise | =1, carry from MSB result=0, if not |
| MOV(.B or .W) src,dst | - | - | - | - |
Notification Switch
Would you like to follow the 'Teaching and classroom laboratories based on the “ez430” and "experimenter's board" msp430 microcontroller platforms and code composer essentials' conversation and receive update notifications?
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|