<< Chapter < Page Chapter >> Page >
This module demonstrates the use of the c28x peripherals and DMC library blocks to control the speed of a DC motor in a closed-loop fashion. This example is based on the "DC Motor Speed Control via RTDX" SIMULINK demo.

Introduction

This chapter demonstrates the use of the c28x peripherals and DMC library blocks to control the speed of a DC motor in a closed-loop fashion. This example is based on the "DC Motor Speed Control via RTDX" SIMULINK demo.

The target speed of the motor is set by the user in the MATLAB GUI. This value is fed to the Controller (based on the eZDSP-F2812) to change the motor speed. The loop is closed by a tachometer. The controller constantly adjusts the value of the DC voltage applied to the motor to maintain the desired speed. The control loop is shown in the following figure:

DC Motor Control Loop

The Speed controller comprises two blocks (please refer to Figure 2):

  1. This block compares the desired speed with the measured speed and generates a digital value proportional to the DC value to be applied to the motor.
    The Speed Controller
  2. This block is implemented using a PWM signal generator and a Low Pass Filter as shown in Figure 3. This method is described in .The output voltage, generated at the LPF output will be:
V = D V ss size 12{V=D cdot V rSub { size 8{ ital "ss"} } } {}

Where:

V size 12{V} {} - Generated Voltage
D size 12{D} {} - PWM Duty Cycle
V ss size 12{V rSub { size 8{ ital "ss"} } } {} - Supply Voltage (3.3 V)
Digital to Analog Converter Implementation

Figure 4 shows the loop control implementation, based on three components:

  1. eZDSP-F2812 (Please refer to )
  2. Interface circuit (Please refer to Section )
  3. DC Motor Kit (Please refer to Section )

DC Motor Control Loop Implementation

Setup

This demo is based on the Spectrum Digital eZdsp-F2812 that is connected to a DC Motor Kit through a dedicated interface circuit. The setup is shown in Figure 5.

Setup

The dc motor kit

Servo amplifier [sa150d]:

This unit operates the motor from signals applied to the input sockets 1 or 2, enabling control of the motor speed and reversing its rotation. This example shows speed control only, and will make use input socket 1 only. The servo amplifier is connected to the servo motor by an 8-pin plug and able. Terminals for ± 15 volts and ground (common) are available on this unit.

Servo motor with tachometer [mt150f]:

This unit is a DC motor that produces a torque of the order of 8 oz-in (600 gm-cm) at 2A input current. The inertia is about 3x10−5 Kg −m2. The output shaft may be fitted with a brake disc and/or an inertia disc to load the motor. A second shaft on the side of the motor is coupled to the main shaft by 30:1 gears (the smaller shaft rotates slower than the main shaft). The tachometer with terminals +, - and common (ground) is attached to the motor.

Power supply [ps150e]:

This unit provides the various voltages supplies required for the servo components. There are terminals for ±15 volts, and common (ground). An ammeter is also included. The maximum current is 2 A. An 8-pin socket and cable connects this unit to the servo amplifier.

Questions & Answers

if three forces F1.f2 .f3 act at a point on a Cartesian plane in the daigram .....so if the question says write down the x and y components ..... I really don't understand
Syamthanda Reply
hey , can you please explain oxidation reaction & redox ?
Boitumelo Reply
hey , can you please explain oxidation reaction and redox ?
Boitumelo
for grade 12 or grade 11?
Sibulele
the value of V1 and V2
Tumelo Reply
advantages of electrons in a circuit
Rethabile Reply
we're do you find electromagnetism past papers
Ntombifuthi
what a normal force
Tholulwazi Reply
it is the force or component of the force that the surface exert on an object incontact with it and which acts perpendicular to the surface
Sihle
what is physics?
Petrus Reply
what is the half reaction of Potassium and chlorine
Anna Reply
how to calculate coefficient of static friction
Lisa Reply
how to calculate static friction
Lisa
How to calculate a current
Tumelo
how to calculate the magnitude of horizontal component of the applied force
Mogano
How to calculate force
Monambi
a structure of a thermocouple used to measure inner temperature
Anna Reply
a fixed gas of a mass is held at standard pressure temperature of 15 degrees Celsius .Calculate the temperature of the gas in Celsius if the pressure is changed to 2×10 to the power 4
Amahle Reply
How is energy being used in bonding?
Raymond Reply
what is acceleration
Syamthanda Reply
a rate of change in velocity of an object whith respect to time
Khuthadzo
how can we find the moment of torque of a circular object
Kidist
Acceleration is a rate of change in velocity.
Justice
t =r×f
Khuthadzo
how to calculate tension by substitution
Precious Reply
hi
Shongi
hi
Leago
use fnet method. how many obects are being calculated ?
Khuthadzo
khuthadzo hii
Hulisani
how to calculate acceleration and tension force
Lungile Reply
you use Fnet equals ma , newtoms second law formula
Masego
please help me with vectors in two dimensions
Mulaudzi Reply
how to calculate normal force
Mulaudzi
Got questions? Join the online conversation and get instant answers!
Jobilize.com Reply

Get Jobilize Job Search Mobile App in your pocket Now!

Get it on Google Play Download on the App Store Now




Source:  OpenStax, From matlab and simulink to real-time with ti dsp's. OpenStax CNX. Jun 08, 2009 Download for free at http://cnx.org/content/col10713/1.1
Google Play and the Google Play logo are trademarks of Google Inc.

Notification Switch

Would you like to follow the 'From matlab and simulink to real-time with ti dsp's' conversation and receive update notifications?

Ask